Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Fast, Reliable Chimney Repair Across Elmhurst
If your chimney is shedding mortar, showing a chalky bloom on the brick, or venting a furnace through a flue that was never built for it, you’re in the right place. We handle chimney repair across Elmhurst, from the brick rowhouses off Broadway to the low-rise apartment buildings near Queens Boulevard. We know this housing stock: early-20th-century masonry, shared stacks, unlined flues. That shapes how we work. Every repair starts with camera documentation you can see for yourself, so nothing gets sold to you blind. Call (855) 410-4917. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Elmhurst Homeowners Call Chimney Sweep Forest Hills for Chimney Repair
We’re a chimney and fireplace specialty contractor, not a general handyman who sweeps on the side. That matters in Elmhurst, where a repair call often uncovers a second problem the sweep alone wouldn’t fix: failing mortar, a cracked crown, a flue that needs relining before it’s safe to use again. We carry five service categories under one roof, sweeping, inspection, cap and crown work, structural repair, and fireplace repair, so a single visit can diagnose and fix.
We work with professional-trade brands that general handymen can’t buy: HeatShield for flue resurfacing, Gelco and Famco for caps and covers, Olympia Chimney and DuraFlex for flexible liner systems. That range means we can reline a compromised flue rather than clean around the problem, and we can resurface deteriorating flue tile with HeatShield instead of tearing it out. Our technicians have up to 8 years of experience. We also serve nearby Rego Park, Corona, Middle Village, and Forest Hills.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Our Chimney Repair Services in Elmhurst
Mortar Repointing
In Elmhurst’s pre-war brick rowhouses, the mortar joints between chimney bricks are often the first thing to go, crumbling and washing out after decades of freeze-thaw cycles. Repointing means raking out the failed mortar and packing fresh mortar into the joints so the stack holds together and water stays out. We match the mortar to the original brick where we can, because a hard modern mortar on soft old brick can actually make spalling worse.

Spalling Brick Repair
Spalling is the white, chalky bloom and flaking face you see on chimney brick, and in this climate it’s usually a symptom rather than a cause. Water gets into the masonry, freezes, expands, and pops the brick face off. We find where the water is entering, usually a failed crown or flashing, and fix that before replacing the damaged brick. Treating the bloom as cosmetic and repointing over it invites the same failure next winter.

Chimney Waterproofing
After the masonry is sound, a breathable waterproofing treatment helps slow the water absorption that drives spalling and freeze-thaw damage through Elmhurst’s humid summers and cold winters. We use a vapor-permeable product so the brick can still breathe; a sealed, non-breathable coating traps moisture inside and can worsen the problem. Waterproofing is a finish, not a repair, so we recommend it only once the crown, flashing, and mortar are in shape.

Flashing Repair
Flashing is the metal where the chimney meets the roof, and when it fails, water runs straight into the masonry and the ceiling below. In the dense building line around Elmhurst, we see old flashing that’s pulled loose or rusted through on stacks that have never been properly maintained. We repair or replace the flashing and seal it correctly so the roof-to-chimney joint sheds water the way it should.
Trusted Brands We Service in Elmhurst
We work with a curated set of professional-grade chimney brands, and that shapes what we can actually fix. HeatShield lets us resurface a deteriorating flue instead of demolishing it. Gelco and Famco caps and covers solve the moisture and animal intrusion that starts most chimney damage, often at the same visit as a sweep. Olympia Chimney and DuraFlex flexible liner systems let us bring older or converted chimneys up to a safe, code-compliant flue. These are products certified chimney professionals specify, not general handyman stock. We don’t claim parts on a truck; we diagnose, specify the right product, and get it done.
Common Chimney Repair Problems We See in Elmhurst Homes
- Shared stacks between rowhouse units. In Elmhurst’s 1920s-1940s brick rowhouses, one masonry stack often serves more than one unit, so any repair has to start by documenting which flue serves which appliance and whether unlined sections are shared. Sealing or venting the wrong flue can affect a neighbor.
- Unlined or clay-tile flues venting modern appliances. Many of these chimneys were built for coal or oil and later converted, so furnace and water heater gases now run through flues never designed for them. Flue-tile integrity checks and parging are standard on nearly every Elmhurst call.
- Spalling brick and a cracked crown. The white bloom and flaking face on exterior brick usually trace back to water entering through a failed crown or flashing. Repointing without fixing the water source just postpones the failure.
- Poor draft from the dense building line. Surrounding structures and shared stacks can hurt draft, and the fix isn’t always a taller chimney. A proper inspection tells you whether it’s a venting issue, a flue-size problem, or blocked flue.
See the difference
Before
After
Before
After
Before
AfterPricing for Chimney Repair in Elmhurst, NY
Chimney repair pricing is per job, set by a written estimate after we’ve seen the camera evidence, so you know what you’re approving and why. Typical estimates in Elmhurst’s market run roughly $350-$900 for mortar repointing on a standard stack, $600-$1,800 for spalling brick repair depending on how much brick is replaced, $400-$900 for flashing repair, and $500-$1,200 for waterproofing after the masonry is sound. A crown repair or rebuild generally runs $400-$1,500, and a HeatShield flue resurfacing typically runs $1,500-$3,000. Those ranges shift with height, access, and how much hidden damage the camera reveals. The written estimate is the final price. Estimates are free.
We Also Serve Cities Near Elmhurst
Elmhurst sits close to a lot of the same pre-war brick housing, so our work frequently crosses into Rego Park, Corona, Middle Village, and Forest Hills. The building stock in these neighborhoods shares the same challenges: aging masonry, converted flues, and shared stacks. If you’re just outside Elmhurst, reach out and we’ll confirm coverage before booking.
Serving Elmhurst, NY – Our Local Coverage Area
We serve Elmhurst and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Chimney Repair in Elmhurst
Yes, an unlined flue built for coal can usually be relined for a modern furnace, but only after a camera inspection confirms the condition of the original flue and which appliance is venting into it. A flexible liner system sized to the appliance is the typical fix, and code requires the liner match the appliance’s venting needs. We won’t recommend relining without showing you the camera footage of gaps, cracks, or missing clay tile. Call (855) 410-4917 for an exact quote – estimates are free.
A crown that’s cracked, crumbling, or pulling away from the flue is the tell, and on a 1930s Elmhurst brick home that’s often visible from the ground as a hairline crack or missing chunk at the top. The crown is the concrete cap that sheds water off the top of the stack, so when it fails, water gets into the masonry. We confirm with a close inspection and camera. Call (855) 410-4917 for an exact quote – estimates are free.
Repointing is raking out failed mortar and packing in fresh mortar; tuckpointing is a finer finish that adds a contrasting mortar line for appearance. For most Elmhurst chimneys, the real need is repointing to restore structural soundness, not tuckpointing for looks. We’ll tell you plainly which your stack needs. Call (855) 410-4917 for an exact quote – estimates are free.
Yes, when it’s a breathable, vapor-permeable treatment, which lets the original brick dry out instead of trapping moisture inside. A non-breathable sealant on soft pre-war brick can make spalling worse. We apply waterproofing only after the crown, flashing, and mortar are repaired. Call (855) 410-4917 for an exact quote – estimates are free.
Know which flue serves which unit before anyone touches the stack, and get that documented so both sides understand what’s being repaired and how the shared flues stay properly sealed and vented. Shared stacks are common in Elmhurst rowhouses, and improper sealing can affect the neighbor’s venting. We document the configuration with camera evidence first. Call (855) 410-4917 for an exact quote – estimates are free.
What Happens When You Call
When you call, we book an inspection and repair visit, and we start with a Level 2 inspection with camera documentation so you see exactly what we see. Then we walk you through the findings: what needs fixing now, what can safely wait, and what the written estimate covers. No repair is recommended without camera evidence. Call (855) 410-4917. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. The estimate is free, and the price is set per job.
Written by the team at Chimney Sweep Forest Hills.