Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Fast, Reliable Chimney Cap & Crown Across Franklin Square
If your chimney cap blew off in a storm or your crown is crumbling, we handle chimney cap and crown work for homeowners in Franklin Square, NY. We know this hamlet block by block, from the postwar Capes near Franklin Avenue to the newer infill homes off Hempstead Turnpike, and we treat a missing cap or a cracked crown as the start of a real diagnosis, not a sales pitch. Call (855) 410-4917 and we’ll book a visit. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Franklin Square Homeowners Call Chimney Sweep Forest Hills for Chimney Cap & Crown
Most of Franklin Square was built in tight waves, and a lot of it has been renovated or replaced since. That means we meet two very different chimneys here on the same street: original brick stacks with clay tile liners on the old Capes and colonials, and factory-built fireplace units inside prefabricated metal chases on the newer and gut-renovated homes. A cap that fits one is wrong for the other, and getting it wrong causes draft problems and trapped moisture you’ll find out about later.
We work on the whole system, not just the visible soot. Our technicians have up to 8 years of experience, and they read the appliance data plate and measure the flue and chase opening before recommending anything, so the correct replacement is dictated by the unit itself rather than by what fits the brick flue next door. Because Franklin Square lots are so tightly packed, ladder placement often means working from a neighboring driveway or off the flat roof of a rear addition, which is routine for us here rather than a special arrangement.
You get a written estimate with the price set per job, and the estimate is free. Nothing gets recommended without camera evidence you can see for yourself, and we’ll tell you plainly when a repair can safely wait. That’s the whole reason people in Franklin Square call us back: a sweep that finds a problem and can fix it on the same call, without inventing work that isn’t there.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Our Chimney Cap & Crown Services in Franklin Square
We treat caps and crowns as part of one system. A crown sheds water off the top of the stack; a cap keeps rain, animals and debris out of the flue. When one fails, the other usually isn’t far behind, and on Franklin Square’s mix of masonry and prefab chimneys the right fix depends on which kind you have.
Cap Installation
New cap installation in Franklin Square starts with identifying what the chimney actually is. On a brick stack we fit a properly sized cap that matches the flue opening, and on a prefabricated chase we install a manufacturer-specific cap that matches the appliance. We use Gelco and Famco products for this work because they hold up through the humid summers and freeze-thaw winters that come off the South Shore bays.

Cap Replacement
Replacement is the most common call we get on newer Franklin Square homes. Factory-built chase tops and their storm collars corrode or tear loose, and the original cap often looks fine from the ground while water is already tracking down the metal chase. We replace the assembly in kind, matching the brand and flue size so draft stays correct and moisture stays out.

Crown Repair
On the hamlet’s older masonry chimneys, the crown is usually where the damage starts. Coastal humidity and repeated freezing and thawing spall and crack the exterior brick at the crown and shoulders, and once water gets in, the damage works downward. We repair the crown and address the masonry around it rather than capping over a failing top.

Crown Coating
Crown coating is a protective layer for a crown that’s sound but showing its age. It seals the surface against the moisture that drives freeze-thaw damage, and on a newer home’s chase top it can extend the life of a galvanized surface before it rusts through. We’ll tell you when coating makes sense and when a repair is the honest answer instead.
We also handle multi-flue caps and custom caps for Franklin Square chimneys that don’t fit a standard size. Two flues side by side on a shared stack, or a chase with an unusual opening, need a cap built to the measurement rather than forced into place.
Trusted Brands We Service in Franklin Square
We work with professional-grade chimney brands that general handymen don’t carry: DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco and Copperfield. On a prefab chase, DuraFlex and Olympia components let us match the cap and liner to the appliance rather than retrofit something generic. HeatShield resurfacing lets us repair a deteriorating flue without demolition when the tiles are still structurally sound. We don’t stock parts on a truck, so turnaround depends on the specific assembly, but we’ll tell you up front what’s needed and how long it takes. Every product we specify is one the trade specifies, not a hardware-store substitute.
Common Chimney Cap & Crown Problems We See in Franklin Square Homes
This is the part most Franklin Square homeowners don’t hear elsewhere. Cap and crown failures here split cleanly between the newer prefab homes and the hamlet’s older masonry stock, and they fail for different reasons.
- Rusted or torn chase tops on newer homes. Factory-built chase tops and storm collars corrode through or get ripped loose by nor’easters off the South Shore bays, and water runs down the metal chase into the firebox area. It can stain ceilings before anyone thinks to look at the roof.
- Homeowners assuming a 1990s or 2000s prefab needs no service. A manufacturer-specific cap can crack or shift out of place while the house still looks new, and the damage goes unnoticed until the damper or smoke chamber shows water damage. A Level 2 inspection catches it early.
- Generic caps fitted over a prefab chase. When a custom or generic cap is installed without matching the flue size or brand, it restricts draft and traps moisture that corrodes the chase from the inside. The cap looks fine; the chimney isn’t.
- Spalled crowns and shoulders on older brick stacks. The original Capes and colonials here have clay tile liners and masonry crowns that crack and spall through freeze-thaw cycles, and a failing crown lets water into the flue and the surrounding brick.
The local insight that matters most: on Franklin Square’s newer infill and gut-renovated homes, the fireplace is usually a factory-built unit in a prefabricated metal chase with a manufacturer-specific cap, and the crown is a galvanized chase top rather than masonry. The correct replacement part is dictated by the unit’s data plate, not by what fits the brick flue next door. On a newer home with a factory-built fireplace, the original chase-top cap and its storm collar often corrode or tear loose, letting water track down the metal chase and stain ceilings or rust the firebox. Because these assemblies use brand-specific caps and chase tops, a qualified local technician reads the appliance data plate, measures the flue and chase opening, and replaces the cap in kind rather than retrofitting a generic masonry cap. Then a Level 2 inspection confirms the chase, flashing and smoke chamber are still sound even though the house looks new.
See the difference
Before
After
Before
After
Before
AfterPricing for Chimney Cap & Crown in Franklin Square, NY
Cap and crown pricing in Franklin Square depends on whether you have a masonry stack or a prefabricated chase, and on the size and brand of the assembly. These are typical estimated ranges for the local market; the written estimate sets the final price, and it’s free.
- Cap installation, standard masonry flue: typically $250 to $550.
- Cap replacement on a prefab chase, manufacturer-specific: typically $300 to $650.
- Multi-flue or custom cap: typically $450 to $900, depending on size and configuration.
- Crown repair: typically $400 to $1,200, depending on how much masonry is affected.
- Crown coating: typically $250 to $550 for a sound crown that needs protection.
Height, roof pitch and access affect the number. On Franklin Square’s tightly spaced 40- to 60-foot-wide lots, a ladder often can’t be set on the lawn, so work happens from the roof via a neighboring driveway or off a rear addition’s flat roof. That’s a normal setup here, and we account for it up front in the estimate rather than after the fact. Nothing gets recommended without camera evidence you can see, and we’ll say when a repair can safely wait.
We Also Serve Cities Near Franklin Square
We work throughout the surrounding area as well, including Malverne, Garden City Park, New Hyde Park and Manhasset Hills. Same approach everywhere: whole-system diagnosis, brand-matched parts, and a written estimate before anything starts. If you’re in Franklin Square or a neighboring community, call and we’ll book a visit. For more on this service across our coverage area, see our chimney cap & crown page.
Serving Franklin Square, NY – Our Local Coverage Area
We serve Franklin Square and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Chimney Cap & Crown in Franklin Square
Yes, it can still need replacing even if it looks fine from the ground. Factory-built chase tops and their storm collars corrode or tear loose over time, and the damage often shows up inside the chase before it’s visible on the roof. A Level 2 inspection tells you what’s actually going on. Call (855) 410-4917 for an exact quote: estimates are free.
A prefabricated chase needs a manufacturer-specific cap matched to the appliance’s data plate, flue size and chase opening. A generic masonry cap fitted over a prefab chase restricts draft and traps moisture that corrodes the chase. We read the data plate and measure before specifying the part.
You can’t reliably tell from the ground. A masonry chimney has a poured or formed crown; a prefab chase has a galvanized chase top, and each fails differently. The only way to know is to get up there and look. We document what we find with camera evidence you can see. Call (855) 410-4917 for an exact quote: estimates are free.
No. A prefab cap has to match the appliance’s brand and flue size, and dropping on a generic replacement can restrict draft and cause moisture problems. We identify the unit from its data plate and install the right part for it. Call (855) 410-4917 for an exact quote: estimates are free.
It can be, when the crown or chase top is still sound but showing wear. Coating seals the surface against the moisture that drives freeze-thaw damage and can extend the life of a galvanized chase top before it rusts through. We’ll tell you honestly when coating makes sense and when a repair is the better answer. Call (855) 410-4917 for an exact quote: estimates are free.
Book Your Chimney Cap & Crown Visit in Franklin Square
Whether you’ve got a masonry stack on an older Cape or a prefab chase on a newer home, we’ll get up on the roof, look at the actual assembly, and tell you what it needs and what it doesn’t. Nothing is recommended without camera evidence you can see for yourself, and the written estimate sets the final price. Call (855) 410-4917 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening.
Written by the team at Chimney Sweep Forest Hills.