Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Forest Hills Homeowners
A missing cap and a cracked crown are the two failures we see most on the brick chimneys around Forest Hills, and they cause the same chain of damage: water gets into the masonry, freezes, and pushes the brick and mortar apart from the inside. Replacing a cap or repairing a crown is a modest job compared with rebuilding a chimney top, and it’s the repair that ends the leak at its source. Our technicians have up to 8 years of experience, and we work with professional-grade cap and crown products from brands like Gelco and Famco, the same materials chimney professionals specify. We book cap and crown work across Forest Hills, and when a failing cap is spotted during a sweep we can usually correct it on the same visit. Call (855) 410-4917 to set up an estimate.
What Our Chimney Cap & Crown Service Includes
Caps and crowns protect the most exposed part of the chimney, the part that takes the rain, snow, and freeze-thaw cycles that move through Forest Hills every winter. Each job below starts with an assessment of what’s actually failing, then moves to the right repair.
Cap Installation
A chimney cap is the metal cover that sits over the flue opening, and it does two jobs: it keeps rain and snow out of the flue and it stops birds, squirrels, and raccoons from nesting inside. Every open flue needs one, and an uncapped chimney is the single easiest path for water to reach the flue lining and the firebox below. We install caps sized to the flue and the crown, fit them so the mesh screens sit clear of the tile, and secure them against the wind load a roof in this area sees. We use Gelco and Famco caps because they’re built for long service and fit the standard flue sizes we find on Forest Hills homes.

Cap Replacement
A cap that has rusted through, lost its screen, or blown loose in a storm no longer protects anything and should be replaced rather than patched. Single-wall steel caps rust from the inside out, and a rusted cap often means water has already been dripping onto the crown for a season or two. We pull the old cap, inspect the flue tile and crown underneath, and fit a replacement that matches the flue. If the old cap was the wrong size and let water run in around its edges, the new one solves that too.

Crown Repair
The crown is the concrete or mortar cap at the very top of the chimney that slopes away from the flue to shed water, and when it cracks, water runs straight down into the brickwork. Hairline cracks widen with each freeze, and a badly broken crown lets moisture soak the chimney from the top down, which is where most spalling brick and crumbling mortar begins. We remove the failed sections, rebuild the crown with a proper slope so it drains, and seal the joint at the flue so water can’t get behind it.

Crown Coating
Crown coating is a flexible, weather-resistant membrane applied over a crown that’s cracked but still structurally sound, and it seals the surface without a full rebuild. It’s the right call when the crown has surface cracks and minor erosion but the concrete underneath is still solid and the slope still works. We prep the surface, apply the coating across the whole crown and its edges, and it bridges the small cracks that let water in. Coating is a repair that buys years of service when a rebuild isn’t yet needed, and we’ll tell you plainly when it’s the better option.
Multi-Flue Cap
A multi-flue cap covers two or more flue openings under one unit, which is common on the larger chimneys and older houses around Forest Hills with a fireplace and a furnace flue side by side. These caps are custom-fit to the crown footprint so they cover every flue at once and present one clean top. We measure the flue layout and crown, then set a single cap with individual screened openings so each flue still vents correctly. Getting the fit right matters, because a poorly sized multi-flue cap lets water in between the openings instead of keeping it out.
Custom Cap
Some chimneys have an unusual crown shape, an oversized flue, or a draft problem that a stock cap won’t fix, and that’s when a custom cap makes sense. A custom cap is built to the exact dimensions of the flue and crown, so it fits tightly, covers fully, and doesn’t rely on adapters or gaps. We measure on site, work from those dimensions with brands like Gelco and Famco, and set a cap built for the chimney in front of us. If a standard cap will do the job, we’ll say so and save you the custom cost.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
Cap and crown products are not all alike, and knowing how each one fails is part of getting the repair right. We work with Gelco caps and covers, which are built for the chimney trade and hold up well against weather and animal intrusion, and we match the cap to the flue and crown so it seals and vents the way it should. On the crown side, we work with Famco products for cap and cover solutions, and we know where these units tend to wear: the screens, the mounting, and the seal at the crown edge are the first places to check.
We also work with Olympia Chimney and HeatShield where a cap or crown job uncovers a flue problem underneath. HeatShield’s resurfacing system lets us restore deteriorated flue tile without a full teardown, and Olympia Chimney flexible liners handle the relining when the flue has to be brought up to code. The point is that a cap and crown job doesn’t have to stop at the roof: if the assessment turns up a flue that needs attention, we can address it with the same professional-grade materials certified chimney professionals use. Whether your chimney has a Gelco, Famco, Olympia, or any other make of cap, we can help.
Signs You Need Chimney Cap & Crown Right Now
- The cap is rusted, bent, or missing. A rusted-through or storm-damaged cap no longer keeps water or animals out, and an open flue is the fastest way for rain to reach the flue lining and firebox. A loose cap also rattles and can tear free in high wind.
- You see cracks or crumbling concrete on the crown. Cracks in the crown let water run into the brickwork, and each freeze widens them. Catching this early usually means a coating or a targeted repair instead of a rebuild.
- Water stains, damp patches, or a musty smell near the fireplace. These point to moisture coming down through a failed cap or crown. It’s worth checking the chimney top before the damage spreads into the ceiling and walls.
- Birds, squirrels, or insects getting in. An uncapped or screen-damaged flue is a straightforward entry point for wildlife, and nesting material inside a flue is a fire hazard. A proper cap with intact screening closes that path.
- Spalling brick or loose mortar at the top of the chimney. Flaking brick faces and soft mortar near the crown signal that water has been soaking in for a while. The repair starts at the top, sealing the crown and cap so the masonry can dry out.
Our Chimney Cap & Crown Process – Step by Step
- 1
We assess the chimney top on site. We look at the cap, the crown, the flue tile, and the brickwork just below, checking where water is getting in and how far the damage goes. This is where a photo record starts, so you can see what we see.
- 2
We take measurements and document the condition. Flue size, crown footprint, and the slope of the crown all matter for the fix. We photograph the cap and crown and record what we find, so the estimate is based on the actual chimney rather than a guess from the ground.
- 3
We give you a written estimate before any work starts. You get the price for the specific repair, in writing, with the scope laid out. Nothing is added later without your go-ahead, and we tell you when a repair can safely wait.
- 4
We carry out the repair. That can be a new cap, a rebuilt crown with a proper slope, a crown coating, or a custom or multi-flue cap sized to the chimney. We work with Gelco, Famco, Olympia Chimney, and HeatShield materials as the job calls for them.
- 5
We show you the finished work. We photograph the completed cap or crown and check that the seal, slope, and screening are right before we’re done. If the same visit found a flue issue, we walk you through the options so you understand exactly what your chimney needs.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Forest Hills?
Chimney cap and crown work in Forest Hills is priced per job, and the written estimate sets the final number. A typical cap installation runs roughly $250 to $650 depending on flue size and cap type. Cap replacement lands in a similar range. Crown repair is often quoted around $400 to $900, and a crown coating on a sound but cracked crown is generally the lower-cost option. A custom or multi-flue cap sits higher, commonly $700 to $1,500, because it’s built to measure and covers more than one flue. These are estimated ranges for the local market, not fixed prices.
What moves the price is the flue size, the number of flues, the condition of the crown underneath, the cap material, and how much repair the masonry below needs. The way to avoid overpaying is to get a written scope that says exactly what’s being replaced or repaired and why, backed by photos of the problem. Our estimate is free, and it includes the written price, the scope, and a clear note on what can wait. We don’t recommend a rebuild when a coating or a new cap will do the job.
Chimney Cap & Crown Near Forest Hills – Our Service Area
We book cap and crown work across Forest Hills and the surrounding communities, including Rego Park, Kew Gardens, Franklin Square, and New Hyde Park. We also work in Manhasset, Manhasset Hills, New Hyde Park, North New Hyde Park, Franklin Square, North Hills, Garden City Park, Malverne, and Hewlett, so whether you need chimney cap & crown work nearby or a chimney cap & crown assessment a little further out, we can schedule it. Every visit starts with a look at the whole chimney, not just the cap.
If you’d rather start with a full sweep and assessment, our Chimney Sweep Forest Hills service is the place to begin.
Serving Forest Hills, NY – Our Local Coverage Area
We serve Forest Hills and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Forest Hills
A chimney cap is the cover over the flue opening that keeps out rain, snow, and animals, and the crown is the sloped concrete or mortar top that sheds water away from the brickwork. Together they protect the chimney from the water that causes most masonry damage. The cap handles the flue, the crown handles the chimney top, and both need to be intact to keep the chimney dry. When one fails, the other usually follows, which is why we check them together.
Most cap installations and replacements are done in a single visit, often alongside a sweep. Crown repairs and coatings usually take a bit longer because of surface prep, rebuild time, and curing. A custom or multi-flue cap may need a second trip once the unit is built to measure. We’ll give you a realistic timeline in the estimate so you know what to expect.
Cap installation and replacement typically run about $250 to $650, crown repair around $400 to $900, and custom or multi-flue caps commonly $700 to $1,500, all depending on flue size, crown condition, and material. These are estimated ranges, and the written estimate sets the final price. We give you the scope and the number before any work starts, and we tell you when a repair can safely wait. Call (855) 410-4917 for an exact quote – estimates are free.
Yes, we work with Gelco and Famco cap and cover products and know where they tend to wear, from the screens to the seal at the crown. We also work with Olympia Chimney and HeatShield when a job uncovers a flue problem that needs resurfacing or relining. Whether you have one of these brands or any other make of cap, we can assess it and help. The goal is a cap and crown that seal and vent correctly for the chimney you have.
We can often handle cap and crown repairs the same day when they’re simple and the schedule allows. We answer 24/7, and dispatch runs from 7am to 7pm, Sunday through Friday; we’re closed Saturday. A call outside dispatch hours is booked into the next opening. To get on the schedule, call (855) 410-4917 – estimates are free.
Our cap and crown work is backed by a satisfaction guarantee, and the materials come from professional-grade brands like Gelco and Famco built for long service. If something isn’t right with the install, we come back and make it right. We’ll go over the specifics of the guarantee with you at the estimate. Call (855) 410-4917 with any questions – estimates are free.
You don’t need to do much: clear access to the fireplace and the chimney area inside, and let us know about any animals or nests you’ve noticed. Move anything fragile away from the hearth, and secure pets so the technician can get to the roof and the firebox safely. If you know the cap or crown brand, tell us when you book. Then call (855) 410-4917 to schedule – estimates are free.
Schedule Your Chimney Cap & Crown Service in Forest Hills Today
A failing cap or crown is one of the few chimney repairs that can stop water damage before it spreads into the brickwork. We assess the whole chimney top, give you a written estimate, and tell you plainly when a repair can wait. From cap to firebox, one company and one call cover it. Call (855) 410-4917. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Estimates are free and there’s no obligation.
Written by the team at Chimney Sweep Forest Hills.