Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Forest Hills Homeowners
Chimney repair in Forest Hills usually starts with a problem you can see from the sidewalk or smell in the living room: a crown that’s crumbling at the top, a white bloom of efflorescence on the brick, a rust streak down the flashing, or a firebox that smokes no matter what you do with the damper. We work on the whole system, not just the visible soot, which is why a sweep here so often turns into a repair the same visit. Our technicians have up to 8 years of experience and work with professional-grade materials from brands general handymen don’t carry. Same-day repair is often possible. Call (855) 410-4917 and we’ll get an assessment on the books.
What Our Chimney Repair Service Includes
Six repair categories cover nearly everything that goes wrong with a masonry chimney in this part of Queens. Here’s what each one actually addresses.
Mortar Repointing
Repointing is the process of grinding out deteriorated mortar joints and packing in fresh mortar that bonds to the brick rather than sitting on top of it. You need it when joints have receded a quarter inch or more, gone crumbly, or started dropping grit onto the roof. We match the mortar mix and joint profile to the original masonry so the repair doesn’t look patched, and we work in lifts so the wall stays stable while the new mortar cures.

Spalling Brick Repair
Spalling is when the face of a brick pops off or flakes away, usually after water gets in and freezes behind it. You’ll spot it as brick faces lying on the roof, a pitted wall, or bricks that sound hollow when tapped. We cut out the failed units and replace them with brick matched for size and absorption, because dropping in a hard, dense brick next to soft antique ones just moves the failure down the wall.

Chimney Waterproofing
Waterproofing is a breathable vapor-permeable sealer applied to the masonry to keep rain out while letting moisture inside escape. It’s the right call for a chimney with sound brick but a persistent damp problem, efflorescence, or freeze-thaw damage starting to show. We apply it after the masonry has dried and any repointing is finished, so we’re sealing a repaired wall rather than locking moisture into a failing one.

Flashing Repair
Flashing is the metal, usually copper or aluminum, that seals the joint where the chimney meets the roof plane and the counterflashing set into the masonry above it. You need work on it when you see rust staining, a gap at the roofline, or water showing up on the ceiling after a heavy rain. We reset or replace the flashing and cut new counterflashing into the brick so the joint sheds water the way it should, rather than relying on a bead of caulk to hold.
Chimney Rebuilding
Rebuilding means taking the chimney down to a sound course and laying it back up, typically the top few feet above the roofline where freeze-thaw cycles do the most damage. It’s the honest answer when the crown, top courses, and flue tile are all compromised and spot repairs won’t hold another season. We rebuild with new brick, new flue tile where needed, and a properly sloped crown so water runs off instead of pooling at the top.
Tuckpointing
Tuckpointing is the finer version of repointing: a thin, contrasting line of mortar worked into a joint to sharpen the look of the masonry alongside the structural fill. You’d want it on a visible chimney where the brickwork is part of the house’s face and plain repointing would read as a patch. We use it on Forest Hills homes with decorative brick or stone where the repair should disappear into the original detailing.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
We work with a set of professional-trade brands that aren’t sold to general handymen, and knowing how each one behaves is part of what makes a repair last. HeatShield is the cast-in-place liner resurfacing system we use when flue tile is cracked or pitted but the chimney itself is structurally sound: it rebuilds the flue’s inner surface without tearing the chimney apart, which is a repair most sweep-only companies can’t offer. Gelco covers the cap and crown side of the system, and the products hold up well against the freeze-thaw cycling we get here. Olympia Chimney flexible liner systems let us reline a flue properly when the existing tile is too far gone, and Famco caps and covers handle the weather and animal protection that keeps a repaired chimney from failing again.
We’re authorized to work with these brands, which means we can specify the right product for the condition rather than forcing whatever a supply house happens to stock. A reline job with Olympia Chimney reads differently than a HeatShield resurfacing job, and the diagnosis tells us which one your flue actually needs. Whether you have DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, Copperfield, or any other make, we can help.
Signs You Need Chimney Repair Right Now
- Crumbling or missing mortar joints. If you can push a screwdriver into the mortar between bricks, it’s failed. Receded joints let water into the wall, and once it freezes the damage accelerates through the winter.
- White staining on the brick. Efflorescence is salt pushed to the surface by moisture moving through the masonry. It’s a reliable early signal that water is getting in somewhere, whether through the crown, the flashing, or the brick itself.
- Rust streaks or water on the ceiling near the chimney. This usually points to flashing or crown failure. Left alone, a small leak turns into rotted framing and a much larger repair.
- Brick pieces on the roof or in the yard. Spalled brick faces mean the masonry is breaking down from freeze-thaw action. Falling fragments can also damage the roof below, so it’s worth a look sooner than later.
- Smoke coming back into the room or a persistent draft. A blocked or damaged flue, a failed damper, or a liner that’s come apart can all cause this. It’s a sign to stop burning until someone looks at it.
Our Chimney Repair Process – Step by Step
- 1
Book the visit. Call and describe what you’re seeing. We’ll set a window and tell you what to have ready so the assessment goes faster. None of this is guesswork over the phone.
- 2
Inspect the whole system. We look at the firebox, damper, flue, crown, cap, flashing, and the exterior masonry, with a camera run down the flue where the interior condition matters. You get a documented picture of what’s sound and what isn’t.
- 3
Explain the findings and the options. We walk you through what we found with the camera footage in front of you. Your report tells you exactly what your chimney needs, and what it doesn’t, including where a repair can safely wait a season.
- 4
Agree the written estimate. The price is set per job by the written estimate, agreed before any work starts. No surprises added later.
- 5
Do the repair and document it. We carry out the work with professional-grade materials, then show you the finished result, including photos of the repaired masonry or liner where you can’t see it from the ground.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Forest Hills?
Chimney repair in Forest Hills typically runs from a few hundred dollars for a targeted joint or flashing fix up to several thousand for a full rebuild or reline, depending on how much of the system is affected. Here’s how the common scenarios tend to break down:
| Repair | Typical Range | What Drives the Price |
|---|---|---|
| Mortar repointing or tuckpointing | $450 – $1,200 | Linear feet of joint, height above the roof, access |
| Spalling brick repair | $500 – $1,500 | Number of units replaced, matching brick sourcing |
| Chimney waterproofing | $350 – $800 | Masonry surface area, prep work needed first |
| Flashing repair | $400 – $1,100 | Roof pitch, extent of flashing replacement |
| Liner resurfacing (HeatShield) | $1,800 – $3,500 | Flue size, length, condition of existing tile |
| Full chimney rebuild | $3,000 – $8,000+ | Height, tile replacement, crown and cap included |
Height and roof access matter more than people expect: a chimney that’s easy to reach from a low roofline costs less to work on than one that needs staging four stories up. So does the condition of what’s underneath: repointing a wall that’s also taking water through the flashing means you’ll pay for both unless the flashing is fixed first. You avoid overpaying by getting the diagnosis right before anyone picks up a trowel, and by asking for the estimate in writing with the scope spelled out line by line. Our estimate is free, and it includes the camera inspection findings so you can see why each line is there. Call (855) 410-4917 for an exact quote.
Chimney Repair Near Forest Hills – Our Service Area
We cover Forest Hills and the surrounding neighborhoods, including Rego Park and Kew Gardens to the west, plus the Nassau County communities along the corridor: New Hyde Park, North New Hyde Park, Franklin Square, Garden City Park, Manhasset, Manhasset Hills, North Hills, Malverne, and Hewlett. If a sweep in Forest Hills turns up masonry damage, we can often handle the chimney repair on the same visit rather than asking you to book a second appointment. Where a job needs the full system looked at, the Chimney Sweep Forest Hills page covers what a routine sweep and inspection involves.
Serving Forest Hills, NY – Our Local Coverage Area
We serve Forest Hills and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Forest Hills
Chimney repair covers the physical restoration of the chimney structure and flue: mortar repointing, replacing spalled brick, waterproofing the masonry, fixing flashing where it meets the roof, tuckpointing, and full or partial rebuilding. It also includes liner work, such as HeatShield resurfacing or an Olympia Chimney flexible liner installation, when the flue itself is compromised. It’s separate from a sweep, which removes creosote, though a sweep often uncovers the damage that repair addresses. Call (855) 410-4917 if you’re not sure which one you need.
Most repairs finish in a few hours to a full day: repointing, flashing work, waterproofing, and brick replacement all fall into that range. A liner resurfacing or reline usually takes a day; a full rebuild can run two to three days depending on the height and how much tile needs replacing. We’ll tell you the expected duration with the written estimate so you can plan around it.
Typical repairs run from about $350 for waterproofing up to $1,200 or so for repointing, while liner resurfacing lands in the $1,800 – $3,500 range and a full rebuild starts around $3,000. The written estimate sets the final price, and we agree it before any work begins. Call (855) 410-4917 for an exact quote, since estimates are free.
Yes. We’re authorized to work with HeatShield, Gelco, Olympia Chimney, Famco, DuraFlex, and Copperfield, and we know how each product behaves once it’s been in service a while. That means we can diagnose whether a HeatShield-resurfaced flue needs a fresh application or whether an Olympia liner needs a fitting replaced. Whether your chimney has one of these systems or another make entirely, we can help.
Same-day repair is often possible when we have the materials and the diagnosis is straightforward; call and we’ll tell you honestly. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, and the work itself is priced per job by the written estimate, not by the hour it happens.
We stand behind the repairs we carry out and will explain the coverage on your specific job when we give you the written estimate. Masonry repairs and liner work carry different expectations, and we’ll spell out what applies to yours. Ask about it directly during the estimate so there’s no ambiguity later.
Clear the firebox of ash and any remaining wood, and move anything breakable away from the hearth and the floor in front of it. Make sure we can get to the roof or the chimney access point, and let us know in advance if you have a gas log set or an insert, since that changes how we approach the flue. That’s usually all it takes.
Schedule Your Chimney Repair Service in Forest Hills Today
If your chimney is showing its age, don’t wait for a small mortar problem to turn into a full rebuild. Call (855) 410-4917 to book an assessment and a free written estimate. We answer 24/7, fast dispatch runs 7am to 7pm Sunday through Friday, and nothing gets recommended that the camera evidence doesn’t support. From cap to firebox, you get one company and one call.
Written by the team at Chimney Sweep Forest Hills.