Chimney Cap & Crown in Forest Hills, NY | Chimney Sweep Forest Hills

Chimney Cap & Crown in Forest Hills - Made to Fit, Priced in Writing

Caps and crowns measured on your actual flue rather than fitted from a generic box, with one written price covering the part and the fitting.

Call to schedule your free estimate

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Masonry repairMasonry repair
Gas fireplace serviceGas fireplace service
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate

Trusted Chimney Cap & Crown for Forest Hills Homeowners

A missing cap and a cracked crown are the two failures we see most on the brick chimneys around Forest Hills, and they cause the same chain of damage: water gets into the masonry, freezes, and pushes the brick and mortar apart from the inside. Replacing a cap or repairing a crown is a modest job compared with rebuilding a chimney top, and it’s the repair that ends the leak at its source. Our technicians have up to 8 years of experience, and we work with professional-grade cap and crown products from brands like Gelco and Famco, the same materials chimney professionals specify. We book cap and crown work across Forest Hills, and when a failing cap is spotted during a sweep we can usually correct it on the same visit. Call (855) 410-4917 to set up an estimate.

Call (855) 410-4917

What Our Chimney Cap & Crown Service Includes

Caps and crowns protect the most exposed part of the chimney, the part that takes the rain, snow, and freeze-thaw cycles that move through Forest Hills every winter. Each job below starts with an assessment of what’s actually failing, then moves to the right repair.

Cap Installation

A chimney cap is the metal cover that sits over the flue opening, and it does two jobs: it keeps rain and snow out of the flue and it stops birds, squirrels, and raccoons from nesting inside. Every open flue needs one, and an uncapped chimney is the single easiest path for water to reach the flue lining and the firebox below. We install caps sized to the flue and the crown, fit them so the mesh screens sit clear of the tile, and secure them against the wind load a roof in this area sees. We use Gelco and Famco caps because they’re built for long service and fit the standard flue sizes we find on Forest Hills homes.

Cap Installation

Cap Replacement

A cap that has rusted through, lost its screen, or blown loose in a storm no longer protects anything and should be replaced rather than patched. Single-wall steel caps rust from the inside out, and a rusted cap often means water has already been dripping onto the crown for a season or two. We pull the old cap, inspect the flue tile and crown underneath, and fit a replacement that matches the flue. If the old cap was the wrong size and let water run in around its edges, the new one solves that too.

Cap Replacement

Crown Repair

The crown is the concrete or mortar cap at the very top of the chimney that slopes away from the flue to shed water, and when it cracks, water runs straight down into the brickwork. Hairline cracks widen with each freeze, and a badly broken crown lets moisture soak the chimney from the top down, which is where most spalling brick and crumbling mortar begins. We remove the failed sections, rebuild the crown with a proper slope so it drains, and seal the joint at the flue so water can’t get behind it.

Crown Repair

Crown Coating

Crown coating is a flexible, weather-resistant membrane applied over a crown that’s cracked but still structurally sound, and it seals the surface without a full rebuild. It’s the right call when the crown has surface cracks and minor erosion but the concrete underneath is still solid and the slope still works. We prep the surface, apply the coating across the whole crown and its edges, and it bridges the small cracks that let water in. Coating is a repair that buys years of service when a rebuild isn’t yet needed, and we’ll tell you plainly when it’s the better option.

Multi-Flue Cap

A multi-flue cap covers two or more flue openings under one unit, which is common on the larger chimneys and older houses around Forest Hills with a fireplace and a furnace flue side by side. These caps are custom-fit to the crown footprint so they cover every flue at once and present one clean top. We measure the flue layout and crown, then set a single cap with individual screened openings so each flue still vents correctly. Getting the fit right matters, because a poorly sized multi-flue cap lets water in between the openings instead of keeping it out.

Custom Cap

Some chimneys have an unusual crown shape, an oversized flue, or a draft problem that a stock cap won’t fix, and that’s when a custom cap makes sense. A custom cap is built to the exact dimensions of the flue and crown, so it fits tightly, covers fully, and doesn’t rely on adapters or gaps. We measure on site, work from those dimensions with brands like Gelco and Famco, and set a cap built for the chimney in front of us. If a standard cap will do the job, we’ll say so and save you the custom cost.

Need help today?Fast, friendly service and a no-obligation free estimate.

Call (855) 410-4917

Explore

Styles & brands we work with

  • Sweep & inspection
  • Caps & crowns
  • Flue relining
  • Masonry repair
  • Gas fireplace service

Brands We Service for Chimney Cap & Crown

Cap and crown products are not all alike, and knowing how each one fails is part of getting the repair right. We work with Gelco caps and covers, which are built for the chimney trade and hold up well against weather and animal intrusion, and we match the cap to the flue and crown so it seals and vents the way it should. On the crown side, we work with Famco products for cap and cover solutions, and we know where these units tend to wear: the screens, the mounting, and the seal at the crown edge are the first places to check.

We also work with Olympia Chimney and HeatShield where a cap or crown job uncovers a flue problem underneath. HeatShield’s resurfacing system lets us restore deteriorated flue tile without a full teardown, and Olympia Chimney flexible liners handle the relining when the flue has to be brought up to code. The point is that a cap and crown job doesn’t have to stop at the roof: if the assessment turns up a flue that needs attention, we can address it with the same professional-grade materials certified chimney professionals use. Whether your chimney has a Gelco, Famco, Olympia, or any other make of cap, we can help.

Signs You Need Chimney Cap & Crown Right Now

  • The cap is rusted, bent, or missing. A rusted-through or storm-damaged cap no longer keeps water or animals out, and an open flue is the fastest way for rain to reach the flue lining and firebox. A loose cap also rattles and can tear free in high wind.
  • You see cracks or crumbling concrete on the crown. Cracks in the crown let water run into the brickwork, and each freeze widens them. Catching this early usually means a coating or a targeted repair instead of a rebuild.
  • Water stains, damp patches, or a musty smell near the fireplace. These point to moisture coming down through a failed cap or crown. It’s worth checking the chimney top before the damage spreads into the ceiling and walls.
  • Birds, squirrels, or insects getting in. An uncapped or screen-damaged flue is a straightforward entry point for wildlife, and nesting material inside a flue is a fire hazard. A proper cap with intact screening closes that path.
  • Spalling brick or loose mortar at the top of the chimney. Flaking brick faces and soft mortar near the crown signal that water has been soaking in for a while. The repair starts at the top, sealing the crown and cap so the masonry can dry out.

Our Chimney Cap & Crown Process – Step by Step

  1. 1
    We assess the chimney top on site. We look at the cap, the crown, the flue tile, and the brickwork just below, checking where water is getting in and how far the damage goes. This is where a photo record starts, so you can see what we see.
  2. 2
    We take measurements and document the condition. Flue size, crown footprint, and the slope of the crown all matter for the fix. We photograph the cap and crown and record what we find, so the estimate is based on the actual chimney rather than a guess from the ground.
  3. 3
    We give you a written estimate before any work starts. You get the price for the specific repair, in writing, with the scope laid out. Nothing is added later without your go-ahead, and we tell you when a repair can safely wait.
  4. 4
    We carry out the repair. That can be a new cap, a rebuilt crown with a proper slope, a crown coating, or a custom or multi-flue cap sized to the chimney. We work with Gelco, Famco, Olympia Chimney, and HeatShield materials as the job calls for them.
  5. 5
    We show you the finished work. We photograph the completed cap or crown and check that the seal, slope, and screening are right before we’re done. If the same visit found a flue issue, we walk you through the options so you understand exactly what your chimney needs.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

How Much Does Chimney Cap & Crown Cost in Forest Hills?

Chimney cap and crown work in Forest Hills is priced per job, and the written estimate sets the final number. A typical cap installation runs roughly $250 to $650 depending on flue size and cap type. Cap replacement lands in a similar range. Crown repair is often quoted around $400 to $900, and a crown coating on a sound but cracked crown is generally the lower-cost option. A custom or multi-flue cap sits higher, commonly $700 to $1,500, because it’s built to measure and covers more than one flue. These are estimated ranges for the local market, not fixed prices.

What moves the price is the flue size, the number of flues, the condition of the crown underneath, the cap material, and how much repair the masonry below needs. The way to avoid overpaying is to get a written scope that says exactly what’s being replaced or repaired and why, backed by photos of the problem. Our estimate is free, and it includes the written price, the scope, and a clear note on what can wait. We don’t recommend a rebuild when a coating or a new cap will do the job.

Chimney Cap & Crown Near Forest Hills – Our Service Area

We book cap and crown work across Forest Hills and the surrounding communities, including Rego Park, Kew Gardens, Franklin Square, and New Hyde Park. We also work in Manhasset, Manhasset Hills, New Hyde Park, North New Hyde Park, Franklin Square, North Hills, Garden City Park, Malverne, and Hewlett, so whether you need chimney cap & crown work nearby or a chimney cap & crown assessment a little further out, we can schedule it. Every visit starts with a look at the whole chimney, not just the cap.

If you’d rather start with a full sweep and assessment, our Chimney Sweep Forest Hills service is the place to begin.

Serving Forest Hills, NY – Our Local Coverage Area

We serve Forest Hills and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions – Chimney Cap & Crown in Forest Hills

Schedule Your Chimney Cap & Crown Service in Forest Hills Today

A failing cap or crown is one of the few chimney repairs that can stop water damage before it spreads into the brickwork. We assess the whole chimney top, give you a written estimate, and tell you plainly when a repair can wait. From cap to firebox, one company and one call cover it. Call (855) 410-4917. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Estimates are free and there’s no obligation.

Written by the team at Chimney Sweep Forest Hills.

Why Forest Hills Chooses Chimney Sweep Forest Hills

We set the standard for chimney cap & crown in Forest Hills.

Evidence Before Recommendations

Every sweep includes a camera inspection and a photo report. If we find something, you see it before we quote it - no repair is ever recommended on our word alone.

Licensed & Insured

The local pro we connect you with is certified and meets all state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Forest Hills

Getting your chimney cap & crown handled is simple and fast.

1

Call or Request a Free Estimate

Tell us about your chimney cap & crown needs and we provide an upfront, transparent quote with no obligation and no hidden fees.

2

We Book a Time That Works for You

A background-checked, certified technician arrives at the time we agree on.

3

Problem Solved, Guaranteed

We complete the job to your full satisfaction, backed by our warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local chimney cap & crown pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    A local pro comes out to measureLicensed and insured, at a time that suits you. The visit and the quote are both free.
  4. 4
    You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.

What Forest Hills Customers Say

Trusted by homeowners across Forest Hills and surrounding areas.

★★★★★

"He explained what went wrong in plain English, showed me the old part, and didn't make me feel stupid for asking why twice. My dad was a contractor and he would have liked this guy."

Reggie Hampton
★★★★★

"Asked a lot of questions before he came out, which I thought was a good sign. Turned out he was right about what the problem probably was, so it was a quick fix once he got here."

Marisol Mendoza
★★★★★

"Level two inspection before we bought the house. The report was detailed enough to use as a negotiating point and he explained every photo in it."

Carrie Miller

Ready for Chimney Cap & Crown in Forest Hills?

Call now for a free estimate, or request one below. The local pro we connect you with is licensed and insured, and here with fast help in Forest Hills.

(855) 410-4917

Request a Free Estimate in Forest Hills

Tell us about your chimney cap & crown needs. We'll respond within the hour.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Local Service Coverage
Chimney Sweep Forest HillsChimney Sweep Manhasset HillsChimney Sweep New Hyde ParkChimney Sweep North New Hyde ParkChimney Sweep Franklin SquareChimney Sweep ManhassetChimney Sweep North HillsChimney Sweep Garden City ParkChimney Sweep MalverneChimney Sweep HewlettChimney Sweep Rego ParkChimney Sweep Kew GardensChimney Sweep CoronaChimney Sweep Middle VillageChimney Sweep ElmhurstChimney Sweep Richmond HillChimney Cap & Crown Forest HillsChimney Cap & Crown Manhasset HillsChimney Cap & Crown New Hyde ParkChimney Cap & Crown North New Hyde ParkChimney Cap & Crown Franklin SquareChimney Cap & Crown ManhassetChimney Cap & Crown North HillsChimney Cap & Crown Garden City ParkChimney Cap & Crown MalverneChimney Cap & Crown HewlettChimney Cap & Crown Rego ParkChimney Cap & Crown Kew GardensChimney Cap & Crown CoronaChimney Cap & Crown Middle VillageChimney Cap & Crown ElmhurstChimney Cap & Crown Richmond HillChimney Repair Forest HillsChimney Repair Manhasset HillsChimney Repair New Hyde ParkChimney Repair North New Hyde ParkChimney Repair Franklin SquareChimney Repair ManhassetChimney Repair North HillsChimney Repair Garden City ParkChimney Repair MalverneChimney Repair HewlettChimney Repair Rego ParkChimney Repair Kew GardensChimney Repair CoronaChimney Repair Middle VillageChimney Repair ElmhurstChimney Repair Richmond HillChimney Inspection Forest HillsChimney Inspection Manhasset HillsChimney Inspection New Hyde ParkChimney Inspection North New Hyde ParkChimney Inspection Franklin SquareChimney Inspection ManhassetChimney Inspection North HillsChimney Inspection Garden City ParkChimney Inspection MalverneChimney Inspection HewlettChimney Inspection Rego ParkChimney Inspection Kew GardensChimney Inspection CoronaChimney Inspection Middle VillageChimney Inspection ElmhurstChimney Inspection Richmond HillFireplace Repair Forest HillsFireplace Repair Manhasset HillsFireplace Repair New Hyde ParkFireplace Repair North New Hyde ParkFireplace Repair Franklin SquareFireplace Repair ManhassetFireplace Repair North HillsFireplace Repair Garden City ParkFireplace Repair MalverneFireplace Repair HewlettFireplace Repair Rego ParkFireplace Repair Kew GardensFireplace Repair CoronaFireplace Repair Middle VillageFireplace Repair ElmhurstFireplace Repair Richmond Hill
Call Now - We Answer 24/7